POTASSIUM CHLORIDE IN DEXTROSE AND SODIUM CHLORIDE – dextrose, sodium chloride and potassium chloride injection 
B. Braun Medical Inc.

———-

Potassium Chloride in Dextrose and Sodium Chloride Injections USP

DESCRIPTION

(See chart below for quantitative information.)

Potassium Chloride in Dextrose and Sodium Chloride Injections USP are sterile, nonpyrogenic and contain no bacteriostatic or antimicrobial agents. These products are intended for intravenous administration.

The formulas of the active ingredients are:

Ingredients Molecular
Formula
Molecular
Weight
Sodium Chloride USP
Potassium Chloride USP
 NaCl
KCl
 58.44
74.55
      
 Hydrous Dextrose USP    198.17
Composition – Each 100 mL contains:
Solution Hydrous Dextrose USP Sodium Chloride USP Potassium Chloride USP Concentration of Electrolytes (mEq/liter) Calories per
liter
Calculated
Osmolarity
mOsmol/liter
pH
Sodium Potassium Chloride
Water for Injection USP qs
0.15% Potassium Chloride in 3.3% Dextrose and
0.30% Sodium Chloride Injection USP
 3.3 g  0.3 g  0.15 g  51  20  71  110  310  4.4 (3.5–6.5)
0.075% Potassium Chloride in 5% Dextrose and
0.20% Sodium Chloride Injection USP
 5 g  0.2 g  0.075 g  34  10  44  170  340  4.4 (3.5–6.5)
0.15% Potassium Chloride in 5% Dextrose and
0.20% Sodium Chloride Injection USP
 5 g  0.2 g  0.15 g  34  20  54  170  360  4.4 (3.5–6.5)
0.22% Potassium Chloride in 5% Dextrose and
0.20% Sodium Chloride Injection USP
 5 g  0.2 g  0.22 g  34  30  64  170  380  4.4 (3.5–6.5)
0.30% Potassium Chloride in 5% Dextrose and
0.20% Sodium Chloride Injection USP
 5 g  0.2 g  0.3 g  34  40  74  170  400  4.4 (3.5–6.5)
0.15% Potassium Chloride in 5% Dextrose and
0.33% Sodium Chloride Injection USP
 5 g  0.33 g  0.15 g  56  20  76  170  405  4.4 (3.5–6.5)
0.075% Potassium Chloride in 5% Dextrose and
0.45% Sodium Chloride Injection USP
 5 g  0.45 g  0.075 g  77  10  87  170  425  4.4 (3.5–6.5)
0.15% Potassium Chloride in 5% Dextrose and
0.45% Sodium Chloride Injection USP
 5 g  0.45 g  0.15 g  77  20  97  170  445  4.4 (3.5–6.5)
0.22% Potassium Chloride in 5% Dextrose and
0.45% Sodium Chloride Injection USP
 5 g  0.45 g  0.22 g  77  30  107  170  465  4.4 (3.5–6.5)
0.30% Potassium Chloride in 5% Dextrose and
0.45% Sodium Chloride Injection USP
 5 g  0.45 g  0.3 g  77  40  117  170  490  4.4 (3.5–6.5)
0.15% Potassium Chloride in 5% Dextrose and
0.9% Sodium Chloride Injection USP
 5 g  0.9 g  0.15 g  154  20  174  170  600  4.4 (3.5–6.5)
0.30% Potassium Chloride in 5% Dextrose and
0.9% Sodium Chloride Injection USP
 5 g  0.9 g  0.3 g  154  40  194  170  640  4.4 (3.5–6.5)
0.15% Potassium Chloride in 10% Dextrose and
0.20% Sodium Chloride Injection USP
 10 g  0.2 g  0.15 g  34  20  54  340  615  4.4 (3.5–6.5)

The EXCEL® Container is Latex-free, PVC-free, and DEHP-free.

The plastic container is made from a multilayered film specifically developed for parenteral drugs. It contains no plasticizers and exhibits virtually no leachables. The solution contact layer is a rubberized copolymer of ethylene and propylene. The container is nontoxic and biologically inert. The container-solution unit is a closed system and is not dependent upon entry of external air during administration. The container is overwrapped to provide protection from the physical environment and to provide an additional moisture barrier when necessary.

Addition of medication should be accomplished using complete aseptic technique.

The closure system has two ports; the one for the administration set has a tamper evident plastic protector and the other is a medication addition site. Refer to the Directions for Use of the container.

CLINICAL PHARMACOLOGY

These intravenous solutions provide electrolytes and calories, and are a source of water for hydration. They are capable of inducing diuresis depending on the clinical condition of the patient.

Sodium, the major cation of the extracellular fluid, functions primarily in the control of water distribution, fluid balance, and osmotic pressure of body fluids. Sodium is also associated with chloride and bicarbonate in the regulation of the acid-base equilibrium of body fluid.

Potassium, the principal cation of intracellular fluid, participates in carbohydrate utilization and protein synthesis, and is critical in the regulation of nerve conduction and muscle contraction, particularly in the heart.

Chloride, the major extracellular anion, closely follows the metabolism of sodium, and changes in the acid-base balance of the body are reflected by changes in the chloride concentration.

Dextrose provides a source of calories. Dextrose is readily metabolized, may decrease losses of body protein and nitrogen, promotes glycogen deposition and decreases or prevents ketosis if sufficient doses are provided.

INDICATIONS AND USAGE

These intravenous solutions are indicated for use in adults and pediatric patients as sources of electrolytes, calories and water for hydration.

CONTRAINDICATIONS

These solutions are contraindicated where the administration of sodium, potassium or chloride could be clinically detrimental.

Solutions containing dextrose may be contraindicated in patients with hypersensitivity to corn products.

WARNINGS

The administration of intravenous solutions can cause fluid and/or solute overload resulting in dilution of serum electrolyte concentrations, overhydration, congested states or pulmonary edema. The risk of dilutional states is inversely proportional to the electrolyte concentration. The risk of solute overload causing congested states with peripheral and pulmonary edema is directly proportional to the electrolyte concentration.

Solutions containing sodium ions should be used with great care, if at all, in patients with congestive heart failure, severe renal insufficiency, and in clinical states in which there is sodium retention with edema.

In patients with diminished renal function, administration of solutions containing sodium or potassium ions may result in sodium or potassium retention.

Solutions containing potassium ions should be used with great care, if at all, in patients with hyperkalemia, severe renal failure, and in conditions in which potassium retention is present.

PRECAUTIONS

General

These solutions should be used with care in patients with hypervolemia, renal insufficiency, urinary tract obstruction, or impending or frank cardiac decompensation.

Extraordinary electrolyte losses such as may occur during protracted nasogastric suction, vomiting, diarrhea or gastrointestinal fistula drainage may necessitate additional electrolyte supplementation.

Additional essential electrolytes, minerals and vitamins should be supplied as needed.

Sodium-containing solutions should be administered with caution to patients receiving corticosteroids or corticotropin, or to other salt-retaining patients.

Care should be exercised in administering solutions containing sodium or potassium to patients with renal or cardiovascular insufficiency, with or without congestive heart failure, particularly if they are postoperative or elderly.

Potassium therapy should be guided primarily by serial electrocardiograms, especially in patients receiving digitalis. Serum potassium levels are not necessarily indicative of tissue potassium levels. Solutions containing potassium should be used with caution in the presence of cardiac disease, particularly when accompanied by renal disease.

Solutions containing dextrose should be used with caution in patients with overt or known subclinical diabetes mellitus, or carbohydrate intolerance for any reason.

To minimize the risk of possible incompatibilities arising from mixing any of these solutions with other additives that may be prescribed, the final infusate should be inspected for cloudiness or precipitation immediately after mixing, prior to administration, and periodically during administration.

Do not use plastic container in series connection.

If administration is controlled by a pumping device, care must be taken to discontinue pumping action before the container runs dry or air embolism may result. If administration is not controlled by a pumping device, refrain from applying excessive pressure (>300mmHg) causing distortion to the container such as wringing or twisting. Such handling could result in breakage of the container.

These solutions are intended for intravenous administration using sterile equipment. It is recommended that intravenous administration apparatus be replaced at least once every 24 hours. Use only if solution is clear and container and seals are intact.

Laboratory Tests

Clinical evaluation and periodic laboratory determinations are necessary to monitor changes in fluid balance, electrolyte concentrations, and acid-base balance during prolonged parenteral therapy or whenever the condition of the patient warrants such evaluation. Significant deviations from normal concentrations may require tailoring of the electrolyte pattern, in these or alternative solutions.

Carcinogenesis, Mutagenesis, Impairment of Fertility

Studies with Potassium Chloride in Dextrose and Sodium Chloride Injections USP have not been performed to evaluate carcinogenic potential, mutagenic potential, or effects on fertility.

Pregnancy

Teratogenic Effects

Pregnancy Category C. Animal reproduction studies have not been conducted with Potassium Chloride in Dextrose and Sodium Chloride Injections USP. It is also not known whether Potassium Chloride in Dextrose and Sodium Chloride Injections USP can cause fetal harm when administered to a pregnant woman or can affect reproduction capacity. Potassium Chloride in Dextrose and Sodium Chloride Injections USP should be given to a pregnant woman only if clearly needed.

Labor and Delivery

The effects of Potassium Chloride in Dextrose and Sodium Chloride Injections USP on the duration of labor or delivery, on the possibility that forceps delivery or other intervention or resuscitation of the newborn will be necessary, and on the later growth, development, and functional maturation of the child are unknown.

As reported in the literature, potassium containing solutions have been administered during labor and delivery. Caution should be exercised, and the fluid balance, glucose and electrolyte concentrations, and acid-base balance, of both mother and fetus should be evaluated periodically or whenever warranted by the condition of the patient or fetus.

Nursing Mothers

It is not known whether these drugs are excreted in human milk. Because many drugs are excreted in human milk, caution should be exercised when Potassium Chloride in Dextrose and Sodium Chloride Injections USP are administered to a nursing woman.

Pediatric Use

Safety and effectiveness of Potassium Chloride in Dextrose and Sodium Chloride Injections USP in pediatric patients have not been established by adequate and well-controlled studies. However, as referenced in the medical literature, potassium chloride injection has been used to treat pediatric patients with potassium deficiency when oral replacement therapy is not feasible.

For patients receiving potassium supplement at greater than maintenance rates, frequent monitoring of serum potassium levels and serial EKGs are recommended.

Dextrose is safe and effective for the stated indications in pediatric patients (see INDICATIONS AND USAGE). As reported in the literature, the dosage selection and constant infusion rate of intravenous dextrose must be selected with caution in pediatric patients, particularly neonates and low birth weight infants, because of the increased risk of hyperglycemia/hypoglycemia. Frequent monitoring of serum glucose concentrations is required when dextrose is prescribed to pediatric patients, particularly neonates and low birth weight infants.

In neonates or in very small infants even small volumes of fluid may affect fluid and electrolyte balance. Care must be exercised in treatment of neonates, especially pre-term neonates, whose renal function may be immature and whose ability to excrete fluid and solute loads may be limited. Fluid intake, urine output, and serum electrolytes should be monitored closely.

See WARNINGS and DOSAGE AND ADMINISTRATION.

Geriatric Use

Clinical studies of Potassium Chloride in Dextrose and Sodium Chloride Injections USP did not include sufficient numbers of subjects aged 65 and over to determine whether they respond differently from younger subjects. Other reported clinical experience has not identified differences in responses between elderly and younger patients.

In general, dose selection for an elderly patient should be cautious, usually starting at the low end of the dosing range, reflecting the greater frequency of decreased hepatic, renal, or cardiac function, and of concomitant disease or other drug therapy.

These drugs are known to be substantially excreted by the kidney, and the risk of toxic reactions to these drugs may be greater in patients with impaired renal function. Because elderly patients are more likely to have decreased renal function, care should be taken in dose selection, and it may be useful to monitor renal function.

See WARNINGS.

ADVERSE REACTIONS

Reactions which may occur because of the solution or the technique of administration include febrile response, infection at the site of injection, venous thrombosis or phlebitis extending from the site of injection, extravasation and hypervolemia.

Too rapid infusion of hypertonic solutions may cause local pain and venous irritation. Rate of administration should be adjusted according to tolerance. Use of the largest peripheral vein and a small bore needle is recommended. (See DOSAGE AND ADMINISTRATION.)

Symptoms may result from an excess or deficit of one or more of the ions present in the solution; therefore, frequent monitoring of electrolyte levels is essential.

Hypernatremia may be associated with edema and exacerbation of congestive heart failure due to the retention of water, resulting in an expanded extracellular fluid volume.

Reactions reported with the use of potassium-containing solutions include nausea, vomiting, abdominal pain and diarrhea. The signs and symptoms of potassium intoxication include paresthesias of the extremities, areflexia, muscular or respiratory paralysis, mental confusion, weakness, hypotension, cardiac arrhythmias, heart block, electrocardiographic abnormalities and cardiac arrest.

Potassium deficits result in disruption of neuromuscular function, and intestinal ileus and dilatation.

If infused in large amounts, chloride ions may cause a loss of bicarbonate ions, resulting in an acidifying effect.

The physician should also be alert to the possibility of adverse reaction to drug additives. Prescribing information for drug additives to be administered in this manner should be consulted.

If an adverse reaction does occur, discontinue the infusion, evaluate the patient, institute appropriate therapeutic countermeasures and save the remainder of the fluid for examination if deemed necessary.

OVERDOSAGE

In the event of fluid overload during parenteral therapy, reevaluate the patient’s condition, and institute appropriate corrective treatment.

In the event of overdosage with potassium-containing solutions, discontinue the infusion immediately and institute corrective therapy to reduce serum potassium levels.

Treatment of hyperkalemia includes the following:

  1. Dextrose Injection USP, 10% or 25%, containing 10 units of crystalline insulin per 20 grams of dextrose administered intravenously, 300 to 500 mL per hour.
  2. Absorption and exchange of potassium using sodium or ammonium cycle cation exchange resin, orally and as retention enema.
  3. Hemodialysis and peritoneal dialysis. The use of potassium-containing foods or medications must be eliminated. However, in cases of digitalization, too rapid a lowering of plasma potassium concentration can cause digitalis toxicity.

DOSAGE AND ADMINISTRATION

These solutions are for intravenous use only.

Dosage is to be directed by a physician and is dependent upon age, weight, clinical condition of the patient and laboratory determinations. Frequent laboratory determinations and clinical evaluation are essential to monitor changes in blood glucose and electrolyte concentrations, and fluid and electrolyte balance during prolonged parenteral therapy.

When a hypertonic solution is to be administered peripherally, it should be slowly infused through a small bore needle, placed well within the lumen of a large vein to minimize venous irritation. Carefully avoid infiltration.

Usually, up to 40 mEq of potassium per liter daily is sufficient to replace normal loss in adults. Typical infusion rates should not exceed 10 mEq per hour or 120 mEq per day. Pediatric patients may require 2 to 3 mEq per kg of body weight daily. See WARNINGS and PRECAUTIONS for pediatric use.

Fluid administration should be based on calculated maintenance or replacement fluid requirements for each patient.

Dextrose may be administered to normal individuals at a rate of 0.5 g/kg/hour without producing glycosuria. At the maximum infusion rate of 0.8 g/kg/hour, approximately 95% of the dextrose is retained.

Some additives may be incompatible. Consult with pharmacist. When introducing additives, use aseptic techniques. Mix thoroughly. Do not store.

Parenteral drug products should be inspected visually for particulate matter and discoloration prior to administration, whenever solution and container permit.

HOW SUPPLIED

Potassium Chloride in Dextrose and Sodium Chloride Injections USP are supplied in EXCEL® Containers. The 1000 mL containers are packaged 12 per case; the 500 mL and 250 mL containers are packaged 24 per case.

Canada DIN NDC Cat. No. Size
0.15% Potassium Chloride in 3.3% Dextrose and
0.30% Sodium Chloride Injection USP
(20 mEq K+/liter)
 
   01931741  0264-7273-00  L2730  1000 mL
0.075% Potassium Chloride in 5% Dextrose and
0.20% Sodium Chloride Injection USP
(10 mEq K+/liter)
 
   0264-7644-00  L6440  1000 mL
0.15% Potassium Chloride in 5% Dextrose and
0.20% Sodium Chloride Injection USP
(20 mEq K+/liter)
 
   01931598  0264-7645-00  L6450  1000 mL
   0264-7645-10  L6451  500 mL
   0264-7645-20  L6452  250 mL
0.22% Potassium Chloride in 5% Dextrose and
0.20% Sodium Chloride Injection USP
(30 mEq K+/liter)
 
   0264-7646-00  L6460  1000 mL
0.30% Potassium Chloride in 5% Dextrose and
0.20% Sodium Chloride Injection USP
(40 mEq K+/liter)
 
   0264-7648-00  L6480  1000 mL
0.15% Potassium Chloride in 5% Dextrose and
0.33% Sodium Chloride Injection USP
(20 mEq K+/liter)
 
   01931601  0264-7655-00  L6550  1000 mL
0.075% Potassium Chloride in 5% Dextrose and
0.45% Sodium Chloride Injection USP
(10 mEq K+/liter)
 
   0264-7634-00  L6340  1000 mL
0.15% Potassium Chloride in 5% Dextrose and
0.45% Sodium Chloride Injection USP
(20 mEq K+/liter)
 
   01931547  0264-7635-00  L6350  1000 mL
0.22% Potassium Chloride in 5% Dextrose and
0.45% Sodium Chloride Injection USP
(30 mEq K+/liter)
 
   0264-7636-00  L6360  1000 mL
0.30% Potassium Chloride in 5% Dextrose and
0.45% Sodium Chloride Injection USP
(40 mEq K+/liter)
 
   01931571  0264-7638-00  L6380  1000 mL
0.15% Potassium Chloride in 5% Dextrose and
0.9% Sodium Chloride Injection USP
(20 mEq K+/liter)
 
   01931644  0264-7652-00  L6520  1000 mL
0.30% Potassium Chloride in 5% Dextrose and
0.9% Sodium Chloride Injection USP
(40 mEq K+/liter)
 
   0264-7682-00  L6820  1000 mL
0.15% Potassium Chloride in 10% Dextrose and
0.20% Sodium Chloride Injection USP
(20 mEq K+/liter)
 
   0264-7663-20  L6632  250 mL

Exposure of pharmaceutical products to heat should be minimized. Avoid excessive heat. Protect from freezing. It is recommended that the product be stored at room temperature (25°C).

Storage in automated dispensing machines: Brief exposure up to 2 weeks to ultraviolet or fluorescent li­­­­ght does not adversely affect the product labeling legibility; prolonged exposure can cause fading of the red label. Rotate stock frequently.

Rx only
Revised: September 2010
EXCEL is a registered trademark of B. Braun Medical Inc.

Directions for Use of EXCEL® Container

Caution: Do not use plastic container in series connection.

To Open

Tear overwrap down at notch and remove solution container.
Check for minute leaks by squeezing solution container firmly.
If leaks are found, discard solution as sterility may be impaired.
If supplemental medication is desired, follow directions below before preparing for administration.

NOTE: Before use, perform the following checks:

Preparation for Administration

  1. Remove plastic protector from sterile set port at bottom of container.
  2. Attach administration set. Refer to complete directions accompanying set.

To Add Medication

Warning: Some additives may be incompatible.

To Add Medication Before Solution Administration

  1. Prepare medication site.
  2. Using syringe with 18–22 gauge needle, puncture medication port and inner diaphragm and inject.
  3. Squeeze and tap ports while ports are upright and mix solution and medication thoroughly.

To Add Medication During Solution Administration

  1. Close clamp on the set.
  2. Prepare medication site.
  3. Using syringe with 18–22 gauge needle of appropriate length (at least 5/8 inch), puncture resealable medication port and inner diaphragm and inject.
  4. Remove container from IV pole and/or turn to an upright position.
  5. Evacuate both ports by tapping and squeezing them while container is in the upright position.
  6. Mix solution and medication thoroughly.
  7. Return container to in use position and continue administration.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
Made in USA

In Canada, distributed by:
B. Braun Medical Inc.
Scarborough, Ontario M1H 2W4

Y36-002-757   LD-196-1

PRINCIPAL DISPLAY PANEL – 1000 mL Container Label

0.15% Potassium Chloride in
3.3% Dextrose and
0.30% Sodium Chloride
Injection USP

REF L2730-00
NDC 0264-7273-00
DIN 01931741

1000 mL
EXCEL® CONTAINER

20 mEq K+/liter
Y94-003-096 LD-265-1

Each 100 mL contains:
Hydrous Dextrose USP 3.3 g
Sodium Chloride USP 0.3 g
Potassium Chloride USP 0.15 g
Water for Injection USP qs
pH: 4.4 (3.5-6.5)

Calc. Osmolarity: 310 mOsmol/liter
Electrolytes (mEq/liter):
Na+ 51     K+ 20     Cl71

Sterile, nonpyrogenic. Single dose container.

Do not use in series connection.
For intravenous use only. Use only if solution is clear and container and seals are intact.

WARNINGS: Some additives may be incompatible. Consult with pharmacist. When introducing additives, use aseptic techniques. Mix thoroughly. Do not store.

Recommended Storage:
Room temperature (25°C). Avoid excessive heat. Protect from freezing. See Package Insert.


Rx only


EXCEL is a registered trademark of B. Braun Medical Inc.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
1-800-227-2862
www.bbraun.com
Made in USA

In Canada, distributed by:
B. Braun Medical Inc.
Scarborough, Ontario M1H 2W4

Y94-003-064  LD-185-2

Do not remove overwrap until ready for use. After removing the overwrap, check for minute leaks by squeezing container firmly. If leaks are found, discard solution as sterility may be impaired.

EXP
LOT

PRINCIPAL DISPLAY PANEL – 1000 mL Container Label

0.075% Potassium Chloride in
5% Dextrose and
0.45% Sodium Chloride
Injection USP

REF L6340
NDC 0264-7634-00

1000 mL
EXCEL® CONTAINER

10 mEq K+/liter
Y94-003-097 LD-258-1

Each 100 mL contains:
Hydrous Dextrose USP 5 g
Sodium Chloride USP 0.45 g
Potassium Chloride USP 0.075 g
Water for Injection USP qs

pH: 4.4 (3.5-6.5)
Calc. Osmolarity: 425 mOsmol/liter, hypertonic

Electrolytes (mEq/liter):
Na77     K+ 10     Cl87

Sterile, nonpyrogenic. Single dose container.

Do not use in series connection.
For intravenous use only. Use only if solution is clear and container and seals are intact.

WARNINGS: Some additives may be incompatible. Consult with pharmacist. When introducing additives, use aseptic techniques. Mix thoroughly. Do not store.

Recommended Storage:
Room temperature (25°C). Avoid excessive heat.
Protect from freezing. See Package Insert.


Rx only


EXCEL is a registered trademark of B. Braun Medical Inc.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
1-800-227-2862 
www.bbraun.com
Made in USA

Y94-003-065
LD-166-2

Do not remove overwrap until ready for use. After removing the overwrap, check for minute leaks by squeezing container firmly. If leaks are found, discard solution as sterility may be impaired.

EXP
LOT

PRINCIPAL DISPLAY PANEL – 1000 mL Container Label

0.15% Potassium Chloride in
5% Dextrose and
0.45% Sodium Chloride
Injection USP

REF L6350
NDC 0264-7635-00
DIN 01931547

1000 mL
EXCEL® CONTAINER

20 mEq K+/liter
Y94-003-096   LD-265-1

Each 100 mL contains:
Hydrous Dextrose USP 5 g
Sodium Chloride USP 0.45 g
Potassium Chloride USP 0.15 g
Water for Injection USP qs

pH: 4.4 (3.5-6.5)
Calc. Osmolarity: 445 mOsmol/liter, hypertonic

Electrolytes (mEq/liter):
Na+ 77     K+ 20     Cl97

Sterile, nonpyrogenic. Single dose container.

Do not use in series connection.
For intravenous use only. Use only if solution is clear
and container and seals are intact.

WARNINGS: Some additives may be incompatible.
Consult with pharmacist. When introducing additives,
use aseptic techniques. Mix thoroughly. Do not store.

Recommended Storage:
Room temperature (25°C). Avoid excessive heat.
Protect from freezing. See Package Insert.


Rx only

EXCEL is a registered trademark of B. Braun Medical Inc.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
1-800-227-2862
www.bbraun.com
Made in USA

In Canada, distributed by:
B. Braun Medical Inc.
Scarborough, Ontario M1H 2W4

Y94-003-066
LD-158-2

Do not remove overwrap until ready for use. After removing
the overwrap, check for minute leaks by squeezing
container firmly. If leaks are found, discard solution as
sterility may be impaired.

PRINCIPAL DISPLAY PANEL – 1000 mL Container Label

0.22% Potassium Chloride
in 5% Dextrose and
0.45% Sodium Chloride
Injection USP

REF L6360
NDC 0264-7636-00

1000 mL
EXCEL® CONTAINER

30 mEq K+/liter
Y94-003-099   LD-266-1

Each 100 mL contains:
Hydrous Dextrose USP 5 g
Sodium Chloride USP 0.45 g
Potassium Chloride USP 0.22 g
Water for Injection USP qs

pH: 4.4 (3.5-6.5)
Calc. Osmolarity: 465 mOsmol/liter, hypertonic

Electrolytes (mEq/liter):
        Na+  77        K+  30      Cl–  107

Sterile, nonpyrogenic. Single dose container.

Do not use in series connection.
For intravenous use only. Use only if solution is clear and container and seals are intact.

WARNINGS: Some additives may be incompatible. Consult with pharmacist. When introducing additives, use aseptic techniques. Mix thoroughly. Do not store.

Recommended Storage:
Room temperature (25°C). Avoid excessive heat.
Protect from freezing. See Package Insert.

Rx only
EXCEL is a registered trademark of B. Braun Medical Inc.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
1-800-227-2862
www.bbraun.com
Made in USA

Do not remove overwrap until ready for use. After removing the overwrap, check for minute leaks by squeezing container firmly. If leaks are found, discard solution as sterility may be impaired.

Y94-003-067
LD-157-2

EXP                             LOT

PRINCIPAL DISPLAY PANEL – 1000 mL Container Label

0.30% Potassium Chloride
in 5% Dextrose and
0.45% Sodium Chloride
Injection USP

REF L6380
NDC 0264-7638-00
DIN 01931571

1000 mL
EXCEL® CONTAINER

40 mEq K+/liter
Y94-003-100   LD-274-1

Each 100 mL contains:
Hydrous Dextrose USP 5 g
Sodium Chloride USP 0.45 g
Potassium Chloride USP 0.3 g
Water for Injection USP qs

pH: 4.4 (3.5-6.5)
Calc. Osmolarity: 490 mOsmol/liter, hypertonic

Electrolytes (mEq/liter):
      Na+  77      K+  40      Cl  117

Sterile, nonpyrogenic. Single dose container.

Do not use in series connection.
For intravenous use only. Use only if solution is clear and container and seals are intact.

WARNINGS: Some additives may be incompatible. Consult with pharmacist. When introducing additives, use aseptic techniques. Mix thoroughly. Do not store.

Recommended Storage:
Room temperature (25°C). Avoid excessive heat.
Protect from freezing. See Package Insert.


Rx only
EXCEL is a registered trademark of B. Braun Medical Inc.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
1-800-227-2862 www.bbraun.com
Made in USA
In Canada, distributed by:
B. Braun Medical Inc.
Scarborough, Ontario M1H 2W4

Do not remove overwrap until ready for use. After removing the overwrap, check for minute leaks by squeezing container firmly. If leaks are found, discard solution as sterility may be impaired.

Y94-003-068
LD-156-2

EXP                             LOT

PRINCIPAL DISPLAY PANEL – 1000 mL Container Label

0.075% Potassium Chloride in
5% Dextrose and
0.20% Sodium Chloride
Injection USP

REF L6440
NDC 0264-7644-00

1000 mL
EXCEL® CONTAINER

10 mEq K+/liter
Y94-003-097   LD-258-1

Each 100 mL contains:
Hydrous Dextrose USP 5 g
Sodium Chloride USP 0.2 g
Potassium Chloride USP 0.075 g
Water for Injection USP qs

pH: 4.4 (3.5-6.5)
Calc. Osmolarity: 340 mOsmol/liter

Electrolytes (mEq/liter):
      Na+  34      K+  10      Cl  44

Sterile, nonpyrogenic. Single dose container.

Do not use in series connection.
For intravenous use only. Use only if solution is clear
and container and seals are intact.

WARNINGS: Some additives may be incompatible.
Consult with pharmacist. When introducing additives,
use aseptic techniques. Mix thoroughly. Do not store.

Recommended Storage:
Room temperature (25°C). Avoid excessive heat.
Protect from freezing. See Package Insert.


Rx only
EXCEL is a registered trademark of B. Braun Medical Inc.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
1-800-227-2862
www.bbraun.com
Made in USA

Y94-003-069
LD-165-2

Do not remove overwrap until ready for use. After
removing the overwrap, check for minute leaks by
squeezing container firmly. If leaks are found,
discard solution as sterility may be impaired.

EXP                              LOT

PRINCIPAL DISPLAY PANEL – 1000 mL Container Label

0.15% Potassium Chloride in
5% Dextrose and
0.20% Sodium Chloride
Injection USP

REF L6450
NDC 0264-7645-00
DIN 01931598

1000 mL
EXCEL® CONTAINER

20 mEq K+/liter
Y94-003-096 LD-265-1

Each 100 mL contains:
Hydrous Dextrose USP 5 g
Sodium Chloride USP 0.2 g
Potassium Chloride USP 0.15 g
Water for Injection USP qs

pH: 4.4 (3.5-6.5)
Calc. Osmolarity: 360 mOsmol/liter, hypertonic

Electrolytes (mEq/liter):
Na+ 34     K+ 20     Cl54

Sterile, nonpyrogenic. Single dose container.

Do not use in series connection.
For intravenous use only. Use only if solution is clear and container and seals are intact.

WARNINGS: Some additives may be incompatible. Consult with pharmacist. When introducing additives, use aseptic techniques. Mix thoroughly. Do not store.

Recommended Storage:
Room temperature (25°C). Avoid excessive heat. Protect from freezing. See Package Insert.


Rx only


EXCEL is a registered trademark of B. Braun Medical Inc.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
1-800-227-2862
www.bbraun.com
Made in USA

In Canada, distributed by:
B. Braun Medical Inc.
Scarborough, Ontario M1H 2W4

Y94-003-070 LD-163-2

Do not remove overwrap until ready for use. After removing the overwrap, check for minute leaks by squeezing container firmly. If leaks are found, discard solution as sterility may be impaired.

EXP
LOT

PRINCIPAL DISPLAY PANEL – 250 mL Container Label

0.15% Potassium Chloride in
5% Dextrose and 0.20% Sodium
Chloride Injection USP

REF L6452
NDC 0264-7645-20
DIN 01931598

250 mL
EXCEL® CONTAINER

20 mEq K+/liter
Y94-003-109 LD-267-1

Each 100 mL contains: Hydrous Dextrose USP 5 g
Sodium Chloride USP 0.2 g
Potassium Chloride USP 0.15 g
Water for Injection USP qs

pH: 4.4 (3.5-6.5)
Calc. Osmolarity: 360 mOsmol/liter, hypertonic

Electrolytes (mEq/liter):   Na+ 34;     K+ 20;     Cl54

Sterile, nonpyrogenic. Single dose container.
Do not use in series connection.
For intravenous use only. Use only if solution is clear and
container and seals are intact.

WARNINGS: Some additives may be incompatible.
Consult with pharmacist. When introducing additives,
use aseptic techniques. Mix thoroughly. Do not store.

Recommended Storage: Room temperature (25°C). Avoid
excessive heat. Protect from freezing. See Package Insert.


Rx only

EXCEL is a registered trademark of B. Braun Medical Inc.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
Made in USA

In Canada, distributed by:
B. Braun Medical Inc.
Scarborough, Ontario M1H 2W4

Y94-003-071
LD-162-2

Do not remove overwrap until ready for use. After removing the
overwrap, check for minute leaks by squeezing container firmly.
If leaks are found, discard solution as sterility may be impaired.

EXP                                  LOT

PRINCIPAL DISPLAY PANEL – 1000 mL Container Label

0.22% Potassium Chloride in
5% Dextrose and
0.20% Sodium Chloride
Injection USP

REF L6460
NDC 0264-7646-00

1000 mL
EXCEL® CONTAINER

30 mEq K+/liter
Y94-003-099 LD-266-1

Each 100 mL contains:
Hydrous Dextrose USP 5 g
Sodium Chloride USP 0.2 g
Potassium Chloride USP 0.22 g
Water for Injection USP qs

pH: 4.4 (3.5-6.5)
Calc. Osmolarity: 380 mOsmol/liter, hypertonic

Electrolytes (mEq/liter):
Na34     K30     Cl64

Sterile, nonpyrogenic. Single dose container.

Do not use in series connection.
For intravenous use only. Use only if solution is clear
and container and seals are intact.

WARNINGS: Some additives may be incompatible.
Consult with pharmacist. When introducing additives,
use aseptic techniques. Mix thoroughly. Do not store.

Recommended Storage:
Room temperature (25°C). Avoid excessive heat.
Protect from freezing. See Package Insert.


Rx only

EXCEL is a registered trademark of B. Braun Medical Inc.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
1-800-227-2862  www.bbraun.com
Made in USA

Y94-003-072
LD-161-2

Do not remove overwrap until ready for use. After
removing the overwrap, check for minute leaks by
squeezing container firmly. If leaks are found,
discard solution as sterility may be impaired.

EXP
LOT

PRINCIPAL DISPLAY PANEL – 1000 mL Container Label

0.30% Potassium Chloride in
5% Dextrose and
0.20% Sodium Chloride
Injection USP

REF L6480
NDC 0264-7648-00

1000 mL
EXCEL® CONTAINER

40 mEq K+/liter
Y94-003-100 LD-274-1

Each 100 mL contains:
Hydrous Dextrose USP 5 g
Sodium Chloride USP 0.2 g
Potassium Chloride USP 0.3 g
Water for Injection USP qs

pH: 4.4 (3.5-6.5)
Calc. Osmolarity: 400 mOsmol/liter, hypertonic

Electrolytes (mEq/liter):
Na34     K40     Cl74

Sterile, nonpyrogenic. Single dose container.

Do not use in series connection.
For intravenous use only. Use only if solution is
clear and container and seals are intact.

WARNINGS: Some additives may be incompatible.
Consult with pharmacist. When introducing
additives, use aseptic techniques. Mix thoroughly.
Do not store.

Recommended Storage:
Room temperature (25°C). Avoid excessive heat.
Protect from freezing. See Package Insert.


Rx only

EXCEL is a registered trademark of B. Braun Medical Inc.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
1-800-227-2862  www.bbraun.com
Made in USA

Y94-003-073
LD-160-2

Do not remove overwrap until ready for use. After
removing the overwrap, check for minute leaks by
squeezing container firmly. If leaks are found,
discard solution as sterility may be impaired.

EXP
LOT

PRINCIPAL DISPLAY PANEL – 1000 mL Container Label

0.15% Potassium Chloride in
5% Dextrose and
0.9% Sodium Chloride
Injection USP

REF L6520
NDC 0264-7652-00
DIN 01931644

1000 mL
EXCEL® CONTAINER

20 mEq K+/liter
Y94-003-096 LD-265-1

Each 100 mL contains:
Hydrous Dextrose USP 5 g
Sodium Chloride USP 0.9 g
Potassium Chloride USP 0.15 g
Water for Injection USP qs

pH: 4.4 (3.5-6.5)
Calc. Osmolarity: 600 mOsmol/liter, hypertonic

Electrolytes (mEq/liter):
Na+ 154     K+ 20     Cl174

Sterile, nonpyrogenic. Single dose container.

Do not use in series connection.
For intravenous use only. Use only if solution is clear and container and seals are intact.

WARNINGS: Some additives may be incompatible. Consult with pharmacist. When introducing additives, use aseptic techniques. Mix thoroughly. Do not store.

Recommended Storage:
Room temperature (25°C). Avoid excessive heat.
Protect from freezing. See Package Insert.


Rx only


EXCEL is a registered trademark of B. Braun Medical Inc.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
1-800-227-2862  www.bbraun.com
Made in USA

In Canada, distributed by:
B. Braun Medical Inc.
Scarborough, Ontario M1H 2W4

Y94-003-074 LD-155-2

Do not remove overwrap until ready for use. After removing the overwrap, check for minute leaks by squeezing container firmly. If leaks are found, discard solution as sterility may be impaired.

EXP
LOT

PRINCIPAL DISPLAY PANEL – 1000 mL Container Label

0.15% Potassium Chloride in
5% Dextrose and
0.33% Sodium Chloride
Injection USP

REF L6550
NDC 0264-7655-00
DIN 01931601

1000 mL
EXCEL® CONTAINER

20 mEq K+/liter
Y94-003-096 LD-265-1

Each 100 mL contains:
Hydrous Dextrose USP 5 g
Sodium Chloride USP 0.33 g
Potassium Chloride USP 0.15 g
Water for Injection USP qs

pH: 4.4 (3.5-6.5)
Calc. Osmolarity: 405 mOsmol/liter, hypertonic

Electrolytes (mEq/liter):
Na+ 56     K+ 20     Cl76

Sterile, nonpyrogenic. Single dose container.

Do not use in series connection.
For intravenous use only. Use only if solution is clear and container and seals are intact.

WARNINGS: Some additives may be incompatible. Consult with pharmacist. When introducing additives, use aseptic techniques. Mix thoroughly. Do not store.

Recommended Storage:
Room temperature (25°C). Avoid excessive heat.
Protect from freezing. See Package Insert.


Rx only


EXCEL is a registered trademark of B. Braun Medical Inc.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
1-800-227-2862  www.bbraun.com
Made in USA

In Canada, distributed by:
B. Braun Medical Inc.
Scarborough, Ontario M1H 2W4

Y94-003-075
LD-159-2

Do not remove overwrap until ready for use. After removing the overwrap, check for minute leaks by squeezing container firmly. If leaks are found, discard solution as sterility may be impaired.

EXP
LOT

PRINCIPAL DISPLAY PANEL – 250 mL Container Label

0.15% Potassium Chloride in
10% Dextrose and 0.20% Sodium
Chloride Injection USP

REF L6632
NDC 0264-7663-20

250 mL
EXCEL® CONTAINER

20 mEq K+/liter
Y94-003-109 LD-267-1

Each 100 mL contains: Hydrous Dextrose USP 10 g
Sodium Chloride USP 0.2 g
Potassium Chloride USP 0.15 g
Water for Injection USP qs

pH: 4.4 (3.5-6.5)
Calc. Osmolarity: 615 mOsmol/liter, hypertonic

Electrolytes (mEq/liter):   Na+ 34;     K+ 20;     Cl54

Sterile, nonpyrogenic. Single dose container.
Do not use in series connection.
For intravenous use only. Use only if solution is clear
and container and seals are intact.

WARNINGS: Some additives may be incompatible.
Consult with pharmacist. When introducing additives,
use aseptic techniques. Mix thoroughly. Do not store.

Recommended Storage:
Room temperature (25°C). Avoid excessive heat.
Protect from freezing. See Package Insert.


Rx only

EXCEL is a registered trademark of B. Braun Medical Inc.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
Made in USA

Y94-003-076
LD-153-2

Do not remove overwrap until ready for use. After removing the
overwrap, check for minute leaks by squeezing container firmly.
If leaks are found, discard solution as sterility may be impaired.

EXP                                  LOT

PRINCIPAL DISPLAY PANEL – 1000 mL Container Label

0.30% Potassium Chloride in
5% Dextrose and
0.9% Sodium Chloride
Injection USP

REF L6820
NDC 0264-7682-00

1000 mL
EXCEL® CONTAINER

40 mEq K+/liter
Y94-003-100   LD-274-1

Each 100 mL contains:
Hydrous Dextrose USP 5 g
Sodium Chloride USP 0.9 g
Potassium Chloride USP 0.3 g
Water for Injection USP qs

pH: 4.4 (3.5-6.5)
Calc. Osmolarity: 640 mOsmol/liter, hypertonic

Electrolytes (mEq/liter):
      Na+  154     K+  40      Cl  194

Sterile, nonpyrogenic. Single dose container.

Do not use in series connection.
For intravenous use only. Use only if solution is
clear and container and seals are intact.

WARNINGS: Some additives may be incompatible.
Consult with pharmacist. When introducing
additives, use aseptic techniques.
Mix thoroughly. Do not store.

Recommended Storage:
Room temperature (25°C). Avoid excessive heat.
Protect from freezing. See Package Insert.


Rx only
EXCEL is a registered trademark of B. Braun Medical Inc.

B. Braun Medical Inc.
Irvine, CA 92614-5895 USA
1-800-227-2862  www.bbraun.com
Made in USA

Y94-003-077
LD-154-2

Do not remove overwrap until ready for use. After
removing the overwrap, check for minute leaks by
squeezing container firmly. If leaks are found,
discard solution as sterility may be impaired.

EXP                              LOT


POTASSIUM CHLORIDE IN DEXTROSE AND SODIUM CHLORIDE 
dextrose, sodium chloride, and potassium chloride  injection
Product Information
Product Type HUMAN PRESCRIPTION DRUG NDC Product Code (Source) 0264-7273
Route of Administration INTRAVENOUS DEA Schedule     
Active Ingredient/Active Moiety
Ingredient Name Basis of Strength Strength
DEXTROSE (DEXTROSE) DEXTROSE 3.3 g  in 100 mL
SODIUM CHLORIDE (SODIUM CATION) SODIUM CHLORIDE 0.3 g  in 100 mL
POTASSIUM CHLORIDE (POTASSIUM CATION) POTASSIUM CHLORIDE 0.15 g  in 100 mL
Inactive Ingredients
Ingredient Name Strength
WATER  
Product Characteristics
Color      Score     
Shape Size
Flavor Imprint Code
Contains     
Packaging
# NDC Package Description Multilevel Packaging
1 0264-7273-00 12 CONTAINER In 1 CASE contains a CONTAINER
1 1000 mL In 1 CONTAINER This package is contained within the CASE (0264-7273-00)

Marketing Information
Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA019630 02/17/1988

POTASSIUM CHLORIDE IN DEXTROSE AND SODIUM CHLORIDE 
dextrose, sodium chloride, and potassium chloride  injection
Product Information
Product Type HUMAN PRESCRIPTION DRUG NDC Product Code (Source) 0264-7644
Route of Administration INTRAVENOUS DEA Schedule     
Active Ingredient/Active Moiety
Ingredient Name Basis of Strength Strength
DEXTROSE (DEXTROSE) DEXTROSE 5 g  in 100 mL
SODIUM CHLORIDE (SODIUM CATION) SODIUM CHLORIDE 0.2 g  in 100 mL
POTASSIUM CHLORIDE (POTASSIUM CATION) POTASSIUM CHLORIDE 0.075 g  in 100 mL
Inactive Ingredients
Ingredient Name Strength
WATER  
Product Characteristics
Color      Score     
Shape Size
Flavor Imprint Code
Contains     
Packaging
# NDC Package Description Multilevel Packaging
1 0264-7644-00 12 CONTAINER In 1 CASE contains a CONTAINER
1 1000 mL In 1 CONTAINER This package is contained within the CASE (0264-7644-00)

Marketing Information
Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA019630 02/17/1988

POTASSIUM CHLORIDE IN DEXTROSE AND SODIUM CHLORIDE 
dextrose, sodium chloride, and potassium chloride  injection
Product Information
Product Type HUMAN PRESCRIPTION DRUG NDC Product Code (Source) 0264-7645
Route of Administration INTRAVENOUS DEA Schedule     
Active Ingredient/Active Moiety
Ingredient Name Basis of Strength Strength
DEXTROSE (DEXTROSE) DEXTROSE 5 g  in 100 mL
SODIUM CHLORIDE (SODIUM CATION) SODIUM CHLORIDE 0.2 g  in 100 mL
POTASSIUM CHLORIDE (POTASSIUM CATION) POTASSIUM CHLORIDE 0.15 g  in 100 mL
Inactive Ingredients
Ingredient Name Strength
WATER  
Product Characteristics
Color      Score     
Shape Size
Flavor Imprint Code
Contains     
Packaging
# NDC Package Description Multilevel Packaging
1 0264-7645-00 12 CONTAINER In 1 CASE contains a CONTAINER
1 1000 mL In 1 CONTAINER This package is contained within the CASE (0264-7645-00)
2 0264-7645-10 24 CONTAINER In 1 CASE contains a CONTAINER
2 500 mL In 1 CONTAINER This package is contained within the CASE (0264-7645-10)
3 0264-7645-20 24 CONTAINER In 1 CASE contains a CONTAINER
3 250 mL In 1 CONTAINER This package is contained within the CASE (0264-7645-20)

Marketing Information
Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA019630 02/17/1988

POTASSIUM CHLORIDE IN DEXTROSE AND SODIUM CHLORIDE 
dextrose, sodium chloride, and potassium chloride  injection
Product Information
Product Type HUMAN PRESCRIPTION DRUG NDC Product Code (Source) 0264-7646
Route of Administration INTRAVENOUS DEA Schedule     
Active Ingredient/Active Moiety
Ingredient Name Basis of Strength Strength
DEXTROSE (DEXTROSE) DEXTROSE 5 g  in 100 mL
SODIUM CHLORIDE (SODIUM CATION) SODIUM CHLORIDE 0.2 g  in 100 mL
POTASSIUM CHLORIDE (POTASSIUM CATION) POTASSIUM CHLORIDE 0.22 g  in 100 mL
Inactive Ingredients
Ingredient Name Strength
WATER  
Product Characteristics
Color      Score     
Shape Size
Flavor Imprint Code
Contains     
Packaging
# NDC Package Description Multilevel Packaging
1 0264-7646-00 12 CONTAINER In 1 CASE contains a CONTAINER
1 1000 mL In 1 CONTAINER This package is contained within the CASE (0264-7646-00)

Marketing Information
Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA019630 02/17/1988

POTASSIUM CHLORIDE IN DEXTROSE AND SODIUM CHLORIDE 
dextrose, sodium chloride, and potassium chloride  injection
Product Information
Product Type HUMAN PRESCRIPTION DRUG NDC Product Code (Source) 0264-7648
Route of Administration INTRAVENOUS DEA Schedule     
Active Ingredient/Active Moiety
Ingredient Name Basis of Strength Strength
DEXTROSE (DEXTROSE) DEXTROSE 5 g  in 100 mL
SODIUM CHLORIDE (SODIUM CATION) SODIUM CHLORIDE 0.2 g  in 100 mL
POTASSIUM CHLORIDE (POTASSIUM CATION) POTASSIUM CHLORIDE 0.3 g  in 100 mL
Inactive Ingredients
Ingredient Name Strength
WATER  
Product Characteristics
Color      Score     
Shape Size
Flavor Imprint Code
Contains     
Packaging
# NDC Package Description Multilevel Packaging
1 0264-7648-00 12 CONTAINER In 1 CASE contains a CONTAINER
1 1000 mL In 1 CONTAINER This package is contained within the CASE (0264-7648-00)

Marketing Information
Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA019630 02/17/1988

POTASSIUM CHLORIDE IN DEXTROSE AND SODIUM CHLORIDE 
dextrose, sodium chloride, and potassium chloride  injection
Product Information
Product Type HUMAN PRESCRIPTION DRUG NDC Product Code (Source) 0264-7655
Route of Administration INTRAVENOUS DEA Schedule     
Active Ingredient/Active Moiety
Ingredient Name Basis of Strength Strength
DEXTROSE (DEXTROSE) DEXTROSE 5 g  in 100 mL
SODIUM CHLORIDE (SODIUM CATION) SODIUM CHLORIDE 0.33 g  in 100 mL
POTASSIUM CHLORIDE (POTASSIUM CATION) POTASSIUM CHLORIDE 0.15 g  in 100 mL
Inactive Ingredients
Ingredient Name Strength
WATER  
Product Characteristics
Color      Score     
Shape Size
Flavor Imprint Code
Contains     
Packaging
# NDC Package Description Multilevel Packaging
1 0264-7655-00 12 CONTAINER In 1 CASE contains a CONTAINER
1 1000 mL In 1 CONTAINER This package is contained within the CASE (0264-7655-00)

Marketing Information
Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA019630 02/17/1988

POTASSIUM CHLORIDE IN DEXTROSE AND SODIUM CHLORIDE 
dextrose, sodium chloride, and potassium chloride  injection
Product Information
Product Type HUMAN PRESCRIPTION DRUG NDC Product Code (Source) 0264-7634
Route of Administration INTRAVENOUS DEA Schedule     
Active Ingredient/Active Moiety
Ingredient Name Basis of Strength Strength
DEXTROSE (DEXTROSE) DEXTROSE 5 g  in 100 mL
SODIUM CHLORIDE (SODIUM CATION) SODIUM CHLORIDE 0.45 g  in 100 mL
POTASSIUM CHLORIDE (POTASSIUM CATION) POTASSIUM CHLORIDE 0.075 g  in 100 mL
Inactive Ingredients
Ingredient Name Strength
WATER  
Product Characteristics
Color      Score     
Shape Size
Flavor Imprint Code
Contains     
Packaging
# NDC Package Description Multilevel Packaging
1 0264-7634-00 12 CONTAINER In 1 CASE contains a CONTAINER
1 1000 mL In 1 CONTAINER This package is contained within the CASE (0264-7634-00)

Marketing Information
Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA019630 02/17/1988

POTASSIUM CHLORIDE IN DEXTROSE AND SODIUM CHLORIDE 
dextrose, sodium chloride, and potassium chloride  injection
Product Information
Product Type HUMAN PRESCRIPTION DRUG NDC Product Code (Source) 0264-7635
Route of Administration INTRAVENOUS DEA Schedule     
Active Ingredient/Active Moiety
Ingredient Name Basis of Strength Strength
DEXTROSE (DEXTROSE) DEXTROSE 5 g  in 100 mL
SODIUM CHLORIDE (SODIUM CATION) SODIUM CHLORIDE 0.45 g  in 100 mL
POTASSIUM CHLORIDE (POTASSIUM CATION) POTASSIUM CHLORIDE 0.15 g  in 100 mL
Inactive Ingredients
Ingredient Name Strength
WATER  
Product Characteristics
Color      Score     
Shape Size
Flavor Imprint Code
Contains     
Packaging
# NDC Package Description Multilevel Packaging
1 0264-7635-00 12 CONTAINER In 1 CASE contains a CONTAINER
1 1000 mL In 1 CONTAINER This package is contained within the CASE (0264-7635-00)

Marketing Information
Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA019630 02/17/1988

POTASSIUM CHLORIDE IN DEXTROSE AND SODIUM CHLORIDE 
dextrose, sodium chloride, and potassium chloride  injection
Product Information
Product Type HUMAN PRESCRIPTION DRUG NDC Product Code (Source) 0264-7636
Route of Administration INTRAVENOUS DEA Schedule     
Active Ingredient/Active Moiety
Ingredient Name Basis of Strength Strength
DEXTROSE (DEXTROSE) DEXTROSE 5 g  in 100 mL
SODIUM CHLORIDE (SODIUM CATION) SODIUM CHLORIDE 0.45 g  in 100 mL
POTASSIUM CHLORIDE (POTASSIUM CATION) POTASSIUM CHLORIDE 0.22 g  in 100 mL
Inactive Ingredients
Ingredient Name Strength
WATER  
Product Characteristics
Color      Score     
Shape Size
Flavor Imprint Code
Contains     
Packaging
# NDC Package Description Multilevel Packaging
1 0264-7636-00 12 CONTAINER In 1 CASE contains a CONTAINER
1 1000 mL In 1 CONTAINER This package is contained within the CASE (0264-7636-00)

Marketing Information
Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA019630 02/17/1988

POTASSIUM CHLORIDE IN DEXTROSE AND SODIUM CHLORIDE 
dextrose, sodium chloride, and potassium chloride  injection
Product Information
Product Type HUMAN PRESCRIPTION DRUG NDC Product Code (Source) 0264-7638
Route of Administration INTRAVENOUS DEA Schedule     
Active Ingredient/Active Moiety
Ingredient Name Basis of Strength Strength
DEXTROSE (DEXTROSE) DEXTROSE 5 g  in 100 mL
SODIUM CHLORIDE (SODIUM CATION) SODIUM CHLORIDE 0.45 g  in 100 mL
POTASSIUM CHLORIDE (POTASSIUM CATION) POTASSIUM CHLORIDE 0.3 g  in 100 mL
Inactive Ingredients
Ingredient Name Strength
WATER  
Product Characteristics
Color      Score     
Shape Size
Flavor Imprint Code
Contains     
Packaging
# NDC Package Description Multilevel Packaging
1 0264-7638-00 12 CONTAINER In 1 CASE contains a CONTAINER
1 1000 mL In 1 CONTAINER This package is contained within the CASE (0264-7638-00)

Marketing Information
Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA019630 02/17/1988

POTASSIUM CHLORIDE IN DEXTROSE AND SODIUM CHLORIDE 
dextrose, sodium chloride, and potassium chloride  injection
Product Information
Product Type HUMAN PRESCRIPTION DRUG NDC Product Code (Source) 0264-7652
Route of Administration INTRAVENOUS DEA Schedule     
Active Ingredient/Active Moiety
Ingredient Name Basis of Strength Strength
DEXTROSE (DEXTROSE) DEXTROSE 5 g  in 100 mL
SODIUM CHLORIDE (SODIUM CATION) SODIUM CHLORIDE 0.9 g  in 100 mL
POTASSIUM CHLORIDE (POTASSIUM CATION) POTASSIUM CHLORIDE 0.15 g  in 100 mL
Inactive Ingredients
Ingredient Name Strength
WATER  
Product Characteristics
Color      Score     
Shape Size
Flavor Imprint Code
Contains     
Packaging
# NDC Package Description Multilevel Packaging
1 0264-7652-00 12 CONTAINER In 1 CASE contains a CONTAINER
1 1000 mL In 1 CONTAINER This package is contained within the CASE (0264-7652-00)

Marketing Information
Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA019630 02/17/1988

POTASSIUM CHLORIDE IN DEXTROSE AND SODIUM CHLORIDE 
dextrose, sodium chloride, and potassium chloride  injection
Product Information
Product Type HUMAN PRESCRIPTION DRUG NDC Product Code (Source) 0264-7682
Route of Administration INTRAVENOUS DEA Schedule     
Active Ingredient/Active Moiety
Ingredient Name Basis of Strength Strength
DEXTROSE (DEXTROSE) DEXTROSE 5 g  in 100 mL
SODIUM CHLORIDE (SODIUM CATION) SODIUM CHLORIDE 0.9 g  in 100 mL
POTASSIUM CHLORIDE (POTASSIUM CATION) POTASSIUM CHLORIDE 0.3 g  in 100 mL
Inactive Ingredients
Ingredient Name Strength
WATER  
Product Characteristics
Color      Score     
Shape Size
Flavor Imprint Code
Contains     
Packaging
# NDC Package Description Multilevel Packaging
1 0264-7682-00 12 CONTAINER In 1 CASE contains a CONTAINER
1 1000 mL In 1 CONTAINER This package is contained within the CASE (0264-7682-00)

Marketing Information
Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA019630 02/17/1988

POTASSIUM CHLORIDE IN DEXTROSE AND SODIUM CHLORIDE 
dextrose, sodium chloride, and potassium chloride  injection
Product Information
Product Type HUMAN PRESCRIPTION DRUG NDC Product Code (Source) 0264-7663
Route of Administration INTRAVENOUS DEA Schedule     
Active Ingredient/Active Moiety
Ingredient Name Basis of Strength Strength
DEXTROSE (DEXTROSE) DEXTROSE 10 g  in 100 mL
SODIUM CHLORIDE (SODIUM CATION) SODIUM CHLORIDE 0.2 g  in 100 mL
POTASSIUM CHLORIDE (POTASSIUM CATION) POTASSIUM CHLORIDE 0.15 g  in 100 mL
Inactive Ingredients
Ingredient Name Strength
WATER  
Product Characteristics
Color      Score     
Shape Size
Flavor Imprint Code
Contains     
Packaging
# NDC Package Description Multilevel Packaging
1 0264-7663-20 24 CONTAINER In 1 CASE contains a CONTAINER
1 250 mL In 1 CONTAINER This package is contained within the CASE (0264-7663-20)

Marketing Information
Marketing Category Application Number or Monograph Citation Marketing Start Date Marketing End Date
NDA NDA019630 02/17/1988

Labeler – B. Braun Medical Inc. (002397347)
Revised: 08/2011B. Braun Medical Inc.